ITW/RedHead® - TB4G-3830 - 3/8" x 3" Anchor
These anchors come with {M} pieces per box and are designed for fastening to concrete. All orders ship immediately from the Cleveland, Ohio warehouse for delivery in 1 to 3 days.
- Bit size 3/8"
- Minimum embedment 2"
- Thread Length Fully Threaded
- 304 stainless steel clip
- Hot-Dipped Galvanized for use in moist environments
- For use in non-vibratory loading applications
- Packaged with hot-dipped galvanized nuts and washers
- 3/8" thick x 3" overall length
- Spacing between anchors is a minimum of 10 anchor diameters
- Free shipping on orders over $25.00
Products specifications
| Bit Size |
3/8" |
| Country |
American Made |
| Minimum Embedment |
1-1/2" |
| Thread Length |
1-3/4" |
| Thread Type |
3/8" - 16 |
| 2000 PSI Concrete - Pull-Out (lbs.) * |
1223 |
| 2000 PSI Concrete - Shear (lbs.) * |
3238 |
| Type |
Male |
| Primary |
Concrete only |
| Diameter |
3/8" |
| Length |
3" |
| Material |
Galvanized |
| Environment |
Damp |
| Box Qty |
50 |
| Minimum Spacing |
3-3/4" |
| Minimum Edge Distance |
1-7/8" |
| Maximum Fixture Thickness |
1-1/8" |
| Minimum Fixture Hole Diameter (In Place) |
1/2" |
| Minimum Fixture Hole Diameter (Hole Spotted) |
3/8" |
| Length ID Code |
D |
| Maximum Torque |
25 - 30 ft./lbs. |
| Wrench Size For Nut |
9/16" |
| Length Measurement |
End to End |
| Brand Name |
CONFAST |
* Values shown are average ultimate values and are offered only as a guide and are not guaranteed. A safety factor of 4:1 or 25% is generally accepted as a safe working load
Applications
The anchor is made from Carbon Steel, and is Zinc Plated. This anchor is designed for use in Concrete only, and should never be used in block or brick base material.
Environment
The anchor is designed for use in a moist environment.
Hole Diameter/Bit Diameter
The anchor requires a 3/8" hole to be drilled in the base material (Concrete only). The hole should be drilled with carbide tipped bit that meets ANSI standards and used in a hammer drill.
Diameter of Anchor
The diameter of the anchor is 3/8".
Length Anchor
The length of the anchor is 3"
Thread Type
The threads on the anchor are national coarse threads that measures 3/8" with 16 threads per inch, commonly referred to as 3/8"-16.
Thread Length
The length of the threads on the anchor is Fully Threaded in length.
Packaging
The anchor is packaged with 50 pieces per box and is packaged with the correct number and diameter of nuts and washers.
Minimum Embedment
The minimum anchor embedment into the concrete is 2". Therefore, the anchor must be installed so that a minimum of 2" of the anchor is embedded into the concrete.
Depth of Hole
The depth of the hole that is required for the anchor should be a minimum of 1/2" deeper than the anchor will penetrate the concrete. This will allow space for dust created during the installation process to fall, which will prevent the anchor from bottoming out in the hole before full penetration into the concrete.
Fixture Hole Diameter
The hole in the fixture or material being fastened must be larger than the designated diameter of the anchor. The 3/8" diameter anchor requires the hole in the fixture to be 1/2".
Wrench Size
The size of the wrench required to turn the nut to set the anchor is 9/16".
Torque Value
To be set properly in the concrete, the anchor must be torqued to between 25 ft./lbs.
Markings
The anchor is stamped with the letter D+ on the threaded end to allow inspection of the anchor after installation. The letter "D+" designates an overall length of the anchor as between 3" up to, but not including 3-1/2" in length.
Holding Values - Ultimate Load Values in 2000 PSI ConcreteAnchor Size | Minimum Embedment | Pull-Out (lbs.) | Shear (lbs.) |
3/8" x 3" | 2" | -1 | -1 |
